OXIDATION STABILITY OF GASOLINE & AVIATION FUEL-IP 40, ASTM D525, IS 1448, P-28-INDUCTION PERIOD METHOD
Compliance Standards : IP 40, ASTM D525, IS 1448 (P-28), ISO 7536. To determine the oxidation stability of gasoline in finished form only, under accelerated oxidation conditions.
CLEAVELAND FLASH POINT APPARATUS -WITH VOLTAGE VARRIER
This apparatus is used for determination of flash point and fire point of petroleum products open cup flash between 79°C - 400°C as per specification IP 36 and IS: 1448 (P: 69) 2019. COMBINED test system either test by Gas JET or by oil wick arrangement with Voltage Varrier (Copper Coil type) control. The apparatus consists of a cup, heating plate to specific dimension thermometer clip and test flame attachment with swivel joint for passing over test liquid surface in the prescribed manner, Heating is controlled by means of Voltage Varrier fitted to the apparatus. Suitable for operation on 220 Volts 50 cycles AC Circuits. Glass Thermometer IP 28C available at extra cost. Digital Temp.indicator can also be supplied at extra cost
FREEZING POINT APPARATUS - (-70 °C) - (ASTM D1177, ASTM D2386)-
This test is particularly relevant for aviation fuels (e.g., jet fuel) where low-temperature performance is critical for safety and engine operation. As per ASTM D2386 ‑ IP 16 ‑ NFM 07048 ‑ ISO 3013 ‑ DIN 51421. The entire instrument assembly Consists of Unsilvered vacuum flask, Jacketed sample tube, Brass packing gland, Motorized stirrer, Stopper, Clamps, Refrigerated water-bath and Stand. Temperature range from -70°C to 0°C
DIGITAL REDWOOD VISCOMETER NO.1
The Redwood Viscometer is used to determine the kinematic viscosity of petroleum products and other liquid fuels. It measures the time taken for a fixed volume of liquid to flow through a calibrated orifice at a specific temperature. The test is widely used in quality control and classification of lubricating oils and fuel oils
DIGITAL REDWOOD VISCOMETER NO.2
The Redwood Viscometer is used to determine the kinematic viscosity of petroleum products and other liquid fuels. It measures the time taken for a fixed volume of liquid to flow through a calibrated orifice at a specific temperature. The test is widely used in quality control and classification of lubricating oils and fuel oils
EQUILIBRIUM REFLUX BOILING POINT TESTER OF AUTOMOTIVE HYDRAULIC BRAKE FLUID - BIS 8654
Supplied complete with Glassware, Heating unit, stand and a Glass Thermometer.
LEAKAGE TENDENCIES TESTER - ASTM D1263 - FOR WHEEL BEARING GREASE
Compliance Standards : ASTM D1263, FTM 791-3454
COPPER CUM SILVER CORROSION BATH - ASTM D130, IP 227
Complies with - IP 154 & IS 1448 (P 15), ASTM D 130, IP 227, ASTM D4814.
ULTRA LOW TEMP. KINEMATIC VISCOSITY BATH - (-40˚C) - COMPLETE S.S.
Suited for 4 Viscometer at a time. Compliance with ASTM D445, IS 1448 (P 25).
ROUND JAR KINEMATIC VISCOSITY BATH-(ABOVE AMBIENT)-FOR 4 VISCOMETERS
This equipment is used to determine the kinematic and intrinsic viscosity of fuels, lubricants, and petrochemical raw materials at constant temperatures, following ASTM D 445 and similar methods. It features a 4-test bath with a round glass vessel, a digital temperature controller with dual display, and a PT-100 sensor. The temperature range is from 5°C above ambient to 150°C with ±0.5°C accuracy. It includes a motorized stirrer, a lighting attachment, and a universal viscometer holder. The system operates on 230V single phase. Glass U-tube viscometers are available separately.
OXIDATION STABILITY BY ROTATING PRESSURE VESSEL METHOD RPVOT - (ASTM D2272, ASTM D2112)
The Oxidation Stability Tester (RPVOT) is designed to assess the oxidation stability of engine, turbine, and inhibited mineral insulating oils by using the rotating pressure vessel method. It complies with ASTM D2272 and ASTM D2112 standards, incorporating a pressure transmitter, recorder, and specialized software to ensure precise measurements and data management.
COPPER CUM SILVER CORROSION BATH - NON REFRIGERATED - DIGITAL - ASTM D130, IP 227
Complies with following International Standards - IP 154 & IS 1448 (P 15), ASTM D 130, IP 227, ASTM D4814. Bath only, without accessories.
DROP POINT APPARATUS FOR GREASE-ASTM D566, IP 132-MOTORISED STIRRER WITH ACCESSORIES
This test method covers the determination of the dropping point of lubricating grease. This test method is not recommended for use at bath temperatures above 288°C. Supplied without Glass Thermometer
DOUBLE ROW SELF-ALIGNING BALL BEARING-SKF 1306K-IP220, DIN 51802
Imported bearing SKF make, double row self-aligning ball bearing, conforming to SKF 1306K with a steel cage as specified in IP220, DIN 51802 test method
LPG COPPER STRIP CORROSION TEST APP - DIGITAL - ASTM D1838
ASTM D1838 is the standard test method used to detect components in Liquefied Petroleum (LP) gases that are corrosive to copper. This quality control test ensures that LPG will not deteriorate the copper or copper-alloy fittings and connections commonly found in storage, transportation, and utilization equipment. A polished copper strip is immersed in approximately 100 mL of an LPG sample. The sample is held in a specialized pressure cylinder and maintained at a temperature of 37.8°C (100°F) in a water bath for one hour. After one hour, the strip is removed and compared against the ASTM
